SoonPho Motorized Tripod Head with Wireless Remote
I got a very reasonably priced motorized tripod head that can be controlled by a wireless remote. This tripod head is made by SoonPho, and it’s called the ‘M-6 Remote and Tracking PanTilt’.

Motorized head holding a Nikon Z9 with custom Arca Swiss plate
Notice in the shot above that the front of the unit has programming buttons and an information display. Below these control buttons is a switch to go between ‘remote’ operation, OFF, and face-tracking.
Above the front display is the built-in camera used to locate your face and to recognize hand signals.
The panning axis can go through full rotations, while the tilt axis goes as far as 54 degrees. The head can support up to 2 kilograms, assuming that it’s balanced over the center of the unit. Be careful to not use any big telephotos that would put your combined rig over this limit. I have had success controlling loads a few ounces heavier than this limit, but I carefully control getting the center of gravity over the head center.
If you overload the unit, or if the camera/lens gets off-axis due to tilting too much, the unit will simply refuse to tilt until the load is reduced or re-balanced over the tripod center-line.
The motor can be programmed to pan up to 8 different speeds, from 0.05 rotations per minute through 4.0 rotations per minute. The unit can tilt at 8 different speeds, from 0.03 rotations per minute through 0.6 rotations per minute. The minimum speeds are too fast to do star tracking, if you had that in mind.
In the Remote Mode switch position, the main display activates. Press the M button repeatedly to cycle through Channel Number (CH), Panning speed (H) ‘S’, and Tilt speed (V) ‘S’. When the appropriate control number is blinking, you can press ‘+’ or ‘-’ to change the value.

Wireless remote
Note that the left-right (panning) arrows on the remote are ‘selfie’ oriented. The manufacturer assumes you’ll want to command the unit to point toward your own face. For photographers, the panning direction arrows are backwards. This unit has 100 different programmable communications channels, in case someone else is using the channel you have selected.
This unit has a line-of-sight remote wireless range of about 30 meters, but much less when shooting through walls. The motorized head can be controlled via the remote or by hand signals.
The signal indicator on the remote will turn red if it loses communications with the main unit. The remote display also has a battery charge level indicator for the main unit. The remote itself uses 2 AAA batteries.

USB-C charging
The unit has a USB-C charging port on the back, including an indicator light that is red while charging and then turns green when charged. The main unit battery is 3.7V 18650 lithium.
The head’s motor gets its internal lithium battery charged via a USB-C cable, which is included. You can’t use your computer for charging; it requires 5 volts and 2 amp capability. I use my Nikon Z9 USB-C charger to do the job.
The built-in Arca Swiss head holds the included mounting plate that has a standard tripod screw. This plate can be used to attach the also-included phone holder, which has a tripod-screw hole in it. This phone holder is meant for vloggers to film themselves while it tracks their movements.
You can program two different positions, called A and B, and command the unit to travel between them using either the wireless remote or buttons on the main unit. It’s really handy for me to have the A position programmed to be perfectly level and pointing straight ahead on my tripod.
If you use Tracking Mode, you will need to reprogram the A and B positions afterward.

Phone holder for vlogging
Note the unit’s built-in camera below the phone. To use this camera, switch the control to the “Tracking” position. The camera understands hand signals to start and stop panning, and it can track a face.

Hand signal to “start tracking my face”
The tracking motion is panning-only. You need to make sure you program the panning speed to be fast enough to be able to follow you.
When the unit recognizes your “OK” to start tracking, it illuminates a green light.

Hand signal to “stop tracking”
When the unit recognizes your “STOP” signal, it will illuminate a red light and stops panning/tracking.

Remote shutter release cable attached to Nikon Z9 camera
The head also includes a 3.5mm TRS (tip,ring,sleeve) stereo receptacle that you can use to remotely trip your camera shutter. You’ll need to provide your own wired cable that’s compatible with your camera.
The TRS shutter receptacle is on the rear of the unit. The remote’s center button (the image of a camera on the button) triggers the shutter release.
Note in the shot above that the unit includes a bubble level next to the TRS shutter receptacle.

Shutter release cord suitable for my Nikon Z9 camera

Tethered shooting (Ethernet cable)
The reason I got this unit is for tethered shooting, where I can adjust the camera position by looking at a live view on my computer monitor and using the wireless remote. I can trigger the camera shutter via the tethering program I use, rather than relying upon the remote shutter release built into the tripod head.
I substituted a different Arca Swiss-compatible slide to hold my camera, instead of the short 2.5 inch (6 cm) slide that is included with the unit. I need a longer slide to balance the camera/lens combination over the tripod center-line.
No, this tripod head isn’t weather-proof.
You can jiggle this motorized head a bit by hand when it’s stationary; it’s not something that Hollywood would want to depend upon. For still photography positioning, it works fine. To me, it’s incredible to imagine all of the features that this unit offers for the price. I bought mine through Amazon.




















Comments